Furnace Installation and Replacement in Spruce Grove and Stony Plain
Furnace installation and replacement: sizing a new high-efficiency furnace, removing the old one, and handling the gas line, venting, permit and start-up.
Installing a furnace is more than setting a unit in place. It has to be sized for your home, connected to gas, power, ductwork and the thermostat, and vented safely outside. Replacing one adds a step: removing the old unit and making sure the existing venting and ducts suit the new one.
Replacement is often the better choice when a furnace is older, needs repeated repairs, or has a serious problem like a cracked heat exchanger. Many gas furnaces last about 15 to 20 years with regular care, so if yours is in that range and starting to fail, get a replacement price alongside any repair quote.
In Alberta, gas work needs a safety codes permit before it starts and must follow the natural gas installation code (CSA B149.1). Most new gas furnaces sold in Canada must be at least 95% AFUE, which means a high-efficiency condensing furnace that vents through plastic pipes and needs a drain for the water it produces.
Signs you need Furnace Installation and Replacement
- The furnace is 15 years old or more and starting to fail
- Repairs are getting more frequent or more expensive
- Heating bills keep climbing
- A technician has found a cracked heat exchanger
- Rust, soot or scorch marks around the furnace
- You're building, adding a suite or developing a basement and need new heating
Common problems
- A furnace sized by guesswork instead of a heat loss calculation
- Old venting that doesn't suit a new high-efficiency furnace
- Ductwork too small or leaky to move the air a new furnace needs
- Vent pipes placed where snow or drifts can block them
- Gas work done without a permit or inspection
What the job involves
- A heat loss calculation to size the furnace
- Getting the gas permit
- Removing and disposing of the old furnace, if there is one
- Installing the furnace, gas line, vent pipes, condensate drain, duct connections and thermostat
- Starting the furnace and testing gas pressure, combustion and safety controls
- Inspection of the gas work under the permit
Furnace Installation and Replacement by area
Furnace Installation and Replacement questions
How do I know it's time to replace my furnace?
Consider replacement when your furnace is older, breaks down often, costs more to run each year, or has a safety problem like a cracked heat exchanger. If a repair would cost a large share of a new furnace, get a replacement price too.
How long does a furnace last?
Many gas furnaces last about 15 to 20 years, and regular maintenance helps them last longer. Age alone isn't a reason to replace a furnace that works well, but it's a good time to start planning.
Do I need a permit to install or replace a furnace in Alberta?
Yes. Under Alberta's Safety Codes Act, gas work needs a safety codes permit before it starts. Your municipality issues the permit and arranges the inspection, so ask your installer who will apply for it.
What size furnace do I need?
The right size depends on how much heat your home loses, not just its square footage. A heat loss calculation looks at insulation, windows, air leaks and layout. An oversized furnace can short cycle, and an undersized one can struggle on the coldest days.
What does AFUE mean?
AFUE stands for annual fuel utilization efficiency. It's the share of the fuel's energy that becomes heat for your home over a year. Natural Resources Canada sets the minimum for most new gas furnaces at 95% AFUE.
Will a new furnace lower my heating bills?
Often, yes, if you're replacing an older, lower-efficiency furnace. How much you save depends on how efficient the old furnace was and how well your home is insulated.
Is a cracked heat exchanger dangerous?
It can be. A cracked heat exchanger can let combustion gases, including carbon monoxide, into the air in your home. If a technician finds one, stop using the furnace until it's dealt with, and make sure your carbon monoxide alarms work.
Can I install a furnace myself?
Gas work in Alberta must be done under a permit and meet the gas code. Rules for homeowner gas permits vary by municipality and are strict, so check with yours first. For most people, a certified gas fitter is the safe choice.